Dura - Manifolds

Fittings as multiple manifold for valve Distribution

With the help of DURA's multiple manifold you can build up an optimal valve distribution. The advantage of using union fittings is the ease of maintenance during later use. You can screw solenoid valves from Hunter, Rain Bird or Gardena into the existing internal threads of the manifold. The smooth faces of the solenoid valves are pressed onto the O-ring integrated in the manifold. This seals the entire valve manifold when hand tightened. The DURA fittings allow easy removal of valves for service, for example, even after many years. In contrast to the fixed screw connection, this fitting offers sufficient space to replace individual parts from the manifold. Professional tip: Install the manifold in such a way that, for example, solenoid valves can be accessed from the right and left via union fittings. Then it is not necessary to disconnect PE lines or to disassemble the entire manifold from one end to replace a defective fitting in the middle!

DURA fittings are all 1" in size and are ideally suited for garden irrigation projects. A reducer fitting (1" male x 3/4" male) allows the fittings to be reduced to 3/4" if needed.

Pre-assembled valve boxes and valve manifolds - according to the motto less individual parts less tripping hazards.

Design your valve box individually according to your ideas, or order one of our pre-assembled valve boxes from the Plug&Rain system! In this category you will find a large number of variants with a different number of valves and for all PE pipe sizes (24 mm Blu Lock, 25 mm PE pipe or 32 mm PE pipe).

Assembly and installation - requirements for Fittings

Dura distribution fittings are made of PVC. They are designed so that the manifold can be easily installed in a valve box or mounted on the wall. Dura's union fittings can be hand tightened without tools. All manifold connections have a 1" BSP thread. Combinations of 1" male BSP threads and 1" female threads are available for easy installation and maintenance of irrigation solenoid valves in a valve box. The union fittings allow components to be easily removed from an existing valve manifold for maintenance and replacement. The o-ring seals built into the female fittings automatically become tight when tightened, you don't need Teflon tape / PTFE tape. When installing the Dura manifold, make sure that PE pipes are brought up to the manifold without tension, so that no lateral forces act on the DURA connectors. This can be achieved, for example, by using an additional angle in the PE pipe.

Stable bolting - Safe assembly and good maintenance in the Dura PVC bolting system

The integrated ring seal allows assembly by hand. No Teflon is required. Depending on the number of valves needed to be installed in the manifold, you can use one or more 2-way, 3-way or 4-way PVC manifolds. The characteristics of the fittings are very high quality, the results look top and are something special! A valve exchange is possible at any time due to a telescopic thread of the Dura PVC distributors.

PVC manifold system for irrigation - manifold construction on the wall or in the valve box

With the system of Dura can be built a complete distribution system for garden irrigation. A wall-mounted distribution system allows easy access, while a valve box (plastic housing with a lid at floor level) allows the valves to be installed at the level of the irrigation pipes (about 30 cm below level). In addition to the pre-assembled system Plug&Rain from DVS Beregnung, these parts can be used to construct individual solutions for the pipe distribution system of irrigation. The goal is to have continuous pressure in one area, from there the solenoid valves go off. Each time an irrigation circuit opens - i.e. power is applied by the controller - water flows from the permanent pressure area into the respective sector. The distribution must be drained just like the entire PE pipe system, nozzles and valves in the winter so that there is no frost damage. Simply provide a bend with ball valve and compressed air connection.

1" Solenoid valves with male or female thread - which one fits Dura's PVC manifold?

We are often asked whether it is better to use the model with male thread (AG) or the valve with female thread (IG) for the solenoid valves. In principle, both are possible, but if you have a choice, we tend to use the more stable male thread. In some cases, however, the question does not arise at all, e.g. some models from Rain Bird or Gardena are only available with internal threads. For valves with female threads, the first step is to use, for example, a 1" nipple from Dura (double nipple, gray), then it goes into the union fitting. With cross pieces, the valve manifold can be branched to the right and to the left.

Irrigation - Simply less gardening with a PVC fitting/manifold

Dura PVC fittings are compatible with solenoid valves from Hunter, Rainbird, Toro and Gardena. Sleeve with integral union nuts for easy installation with 1" connectors. A professional pipe manifold system is ideal for optimal irrigation in your garden. The pressure resistance of the fittings is 10 bar. In the online store on the site of DVS Sprinkling you can order the Dura PVC manifolds and other articles and accessories related to irrigation. At our company you can order and buy articles at an optimal price-quality ratio. The standard delivery time for Dura fittings is short, which makes them an excellent choice for quick installations and repairs. www.dvs-beregnung.de offers fast shipping via DHL.

Summary Fittings for valve manifold installation.

Dura Fittings are PVC manifold fittings for valve manifold assembly that can still be opened by hand years later. These fittings offer female threaded connections, self-sealing hand-assembly fittings, and high quality and durability.
Dura unions are professional PVC manifold fittings for mounting a valve manifold. The unions can be opened by hand even after years and allow service and maintenance of an irrigation system. Dura unions come in a variety of styles, so everyone can find a model to fit their needs. Fittings can be wall mounted with clamps or installed in a valve box for easy installation.
The best thing about Dura fittings is their durability. They're made of high-quality PVC material that can withstand extreme temperatures and other weather conditions without corroding or rusting, so you can be sure that your irrigation system will remain free of leaks and problems for years to come. With their high-quality construction, Dura valve fittings offer superior performance and reliability compared to other brands. If you're looking for the best valves on the market, look no further than Dura. With their superior performance, reliable construction and fast delivery times, they're the perfect choice for your irrigation system. Whether you need a single fitting or a complete set of fittings, Dura MSMF is the ideal solution. Get them today and enjoy hassle-free installation and maintenance for years to come!